Home > Error Code > Ultrium 2 Error Codes

Ultrium 2 Error Codes


Check ambient temperature conditions. When fully used and assuming that the connection to the disks does not force the speed to a lower parallel SCSI type, an Ultra 2 (80) connection barely provides enough bandwidth Export the media to clear the state. The drawback of using concurrency is that restore operations take longer. http://centralpedia.com/error-code/ultrium-lto-2-error-6.html

Please try the request again. Power cycle the device. None. Exchange the cleaning tape. 63 Invalid cartridge. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html

Ibm Ultrium Hh4 Error Codes

Parallel SCSI: Ultra 160 LTO-2: GOOD. Server or workstation with RAID VARIABLE. Clearing it is kind of an arm wrestle, turn on and off several times, insert-eject tape several times etc..

Redundancy is not available. When fully used, an Ultra 320 SCSI connection can provide enough bandwidth for the following number of tape drives, assuming 2:1 compression: LTO-2: 2 LTO-3, LTO-4: 1 Ultra 320 is an The event ID is the number on the header line, 0x006E in this example. Ibm Tape Drive Error Codes The subcode indicates which drive sled fan is affected.

A connection with insufficient bandwidth cannot provide enough data for the tape drives to write at full speed. Ultrium 3 Tape Drive Error Codes When multiple LUN support is not enabled, the host computer can see the tape drive, but not the Autoloader. Do not use cartridges that are incompatible with the tape drive. Make sure that the proper device driver is installed for the SCSI host adapter.

If you continue to have problems with a SAS Autoloader, check the following: Ensure that the device is compatible with the SAS host adapter and backup application you plan to use. Ibm Lto 5 Tape Drive Error Code 6 If the connector on the cable is keyed in a different location, not only will the connector not plug in, but the cable probably will not work. Performance impact of various disk connections Connection type Performance impact Recommendations Fibre: 1 GB LTO-2: GOOD. Change the Startup type to Disabled and click OK.

  1. Upgrade to Ultra 320 for parallel SCSI disk drives when using an LTO-3 or LTO-4 tape drive, especially if your data is greater than 2:1 compressible.
  2. NOTE: Many backup applications use their own drivers.
  3. The bus would be saturated when providing 2:1 compressible data to an Ultrium 1760 tape drive.

Ultrium 3 Tape Drive Error Codes

Parallel SCSI: Ultra Wide, Fast Wide POOR. http://en.community.dell.com/support-forums/storage/f/1216/t/19403374 The main error code (0x83) is displayed in parenthesis as the Global error code. Ibm Ultrium Hh4 Error Codes NOTE: Processor speed numbers as based on Intel x86 type processors. Certance Ultrium 2 Discard any tapes that are damaged or past their usage life.

Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? check over here An Ultra 160 connection is barely adequate for an Ultrium 920 tape drive. The entire disk contents is backed up contiguously, without the disk seeking, which prevents performance degradation caused by small or fragmented files. Generate a detailed support file that can be e-mailed or faxed to a support representative for analysis. Hp Ultrium 2 Scsi

When fully used, a 2 GB fibre connection can provide enough bandwidth for an LTO-3 tape drive. Fibre: 4 GB GOOD. Once the tape is rewound, the eject cycle will take fewer than 16 seconds. his comment is here If you are backing up data over a network, consider comparing the performance to a local-only backup.

This length must be included in any calculations of cable length. Ibm Tape Library Error Codes A data cartridge may have been loaded instead of a cleaning cartridge. The device uses two Logical Unit Numbers (LUNs) to control the tape drive (LUN 0) and robotic (LUN 1).

There are three ways to obtain error codes from the device: On the OCP On the RMI On an L&TT support ticket or report Finding error code information on the OCP

Small file size can impact performance. Everything shows all events. To get the best backup and restore performance, use a full-featured backup application. Ibm Ultrium-hh3 Status Lights In some cases, a multi-processor server may be required.

Please try the request again. Use a shorter cable or remove other devices from the bus. Initiate the firmware upgrade process before loading a firmware upgrade tape into the drive. 65 Invalid upgrade cartridge. weblink Found this: ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ultriumgen2ug.pdf

0 Anaheim OP James (Cloud Continuity) Oct 12, 2011 at 10:37 UTC Hey Tom, I would try a couple of things.  First if you push

To improve performance on a disk system, you can use faster disks or add disks. The bar code reader might not be able to read other labels. An Ultra 2(80) connection is inadequate for an LTO-3 or LTO-4 tape drive. top Database backup Performance impact: VARIABLE.

Parallel SCSI: Ultra Wide, Fast Wide Ultra Wide and Fast Wide are inadequate for all of the currently supported tape drives. If necessary, set a static network address instead. If the Media Attention LED is cleared and the drive has been cleaned, and then immediately re-displays each time a particular cartridge is reloaded, that cartridge should be suspected as being If possible, do NOT use a file-by-file backup method.

Native backup applications based on tar, cpio, NT Backup, etc. Verify that the cartridge is a cleaning cartridge. Figure 1: Removable Storage service Right-click Removable Storage again and select Properties. This is most likely caused by a dirty drive that cannot read a tape and marks the tape invalid.

To remove a stuck tape from a storage slot: If the operator control panel or the remote management interface is still operational: Move the tapes from the drives to the magazines Verify that the proper device driver is installed for the SAS host adapter. The mini-SAS connector on the tape drive is keyed at location four, which is the standard location for end devices. If the average file size is less than 64 kb or if the file system is very fragmented, file-by-file backup will have poor performance.