Home > Error Code > Ultrium Lto 3 Error Code 3

Ultrium Lto 3 Error Code 3


Check ambient temperature conditions. Very helpful Somewhat helpful Not helpful End of content United StatesHewlett Packard Enterprise International Start of Country Selector content Select Your Country/Region and Language Click or use the tab key to If you are concerned about viruses and backup performance, perform a virus scan before starting the backup, and shut down the anti-virus software while the backup is running. When fully used and assuming that the connection to the disks does not force the speed to a lower parallel SCSI type, an Ultra 160 connection can provide enough bandwidth for navigate here

In the Administrative Tools, select Services. The device must be supported under both of its side edges or the bottom can bow and impede robotic movement. Make sure that the host adapter is properly seated in the motherboard slot and the operating system correctly detects the host adapter. Reload the magazines with tapes that have passed inspection and new tapes to replace cartridges that did not pass inspection. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html

Ibm Tape Drive Error Codes

The bus would be saturated when providing 2:1 compressible data to an Ultrium 1760 tape drive. A single disk cannot retrieve or write data fast enough for any of the supported tape drives. lifetime subscription one time payment limm→∞134m=0! "I'd love to help kickstart continued development! The recommended number of disks per Ultrium tape drive is: Ultrium 448: 6 Ultrium 920: 15 Ultrium 1760: 20 Also, make sure that the server or workstation is used as little

Do not backup specific records or do a record-by-record backup. There is no grantee that Drives in 2010 will match the specs shown in the PDF above from 2008. Run the wellness test 90 Ends of elevator movement not in expected range Run the wellness test 91 Ends of rotation movement not in expected range 92 Ends of sled movement Ibm Tape Library Error Codes Find the performance impact of your system's file system in Performance impact of various file systems Performance impact of various file systems File system Performance impact Recommendations Disk array GOOD.

Replace the power cord. Check that the device is fully powered up and is not in an error state. LTO-3, LTO-4: POOR. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_xtault.html Do not degauss Ultrium cartridges!

For example, in this case 14 is 2 p.m. Dell Tape Drive Error Codes top SCSI installation problems Problems encountered during installation are usually caused by improper SCSI bus configuration, application software configuration errors, or an incorrectly configured operating system. If there are no bottlenecks and the Autoloader starts having performance problems: Try a new cartridge. Make sure you are using an Ultrium universal cleaning cartridge (see the Tape cartridges section in Tape Cartridges and Magazines ).

  • Thank you, Paul lto-3 share|improve this question asked Dec 10 '09 at 8:11 DO it all Paul 215 add a comment| 4 Answers 4 active oldest votes up vote 1 down
  • If the failure follows the tape cartridge, the tape cartridge is probably at fault.
  • Figure 1: Removable Storage service Right-click Removable Storage again and select Properties.
  • Verify that your HBA is supported by the host computer and qualified with the Autoloader.
  • Your cache administrator is webmaster.
  • If the average file size is less than 64 kb, HP recommends that you use a sequential/image backup that backups the hard drive or LUN image instead of the individual files.
  • If the RMI web page does not display, ping the device’s IP address.

Ibm Ultrium-hh3 Status Lights

An Ultra 2 (80) connection is inadequate for an LTO-3 or LTO-4 tape drive. When fully used, a 2 GB fibre connection can provide enough bandwidth for an Ultrium 1760 tape drive. Ibm Tape Drive Error Codes The device requires an HBA with multiple LUN support and multiple LUN support must be enabled on the host computer. Ibm Lto 5 Tape Drive Error Code 6 The problems and solutions in the troubleshooting tree is updated more frequently than this manual.

Ultrium 1760: GOOD. check over here SCD dot. Expand the event for more information, as shown in Critical event details (Figure 11). The READY light flashes while the tape rewinds. Tape Drive Determined That A Microcode Error Occurred.

Everything shows all events. How do we play with irregular attendance? If the mini-SAS connectors that connect to the tape drive and some HBAs will not plug in, check the key. his comment is here Large files let the disk do less seeking and spend more time doing continuous reads.

I checked the IBM solutions for the codes but this flashing isn't documented at all. Dell Tape Drive Error Code 7 Verify that the device has been configured with a valid static network address or DHCP has been enabled so the device can obtain a network address. This length must be included in any calculations of cable length.

The log entries are displayed in order of most recent to oldest.

Based on the extent of the detection problem, check the following: If neither the application software nor operating system detects the tape drive, or they do not detect both the tape Refer to the manuals supplied with the other devices on the SCSI bus for information on enabling or disabling termination on those devices. Export the media to clear the state. Tape Drive Or Rs-422 Error or to the blogs user Exclusive servers for faster access in peak times, for you and your visitors Reliable feed imports with shorter intervals!

Do not use cartridges that are incompatible with the tape drive. Fault status light (amber LED). 4. Check the cartridge for damage. weblink Image or sequential backup None.

Thanks Paul share|improve this answer answered Dec 16 '09 at 11:14 DO it all Paul 215 add a comment| Your Answer draft saved draft discarded Sign up or log in