If booting from a hard-disk drive, ensure the hard-disk drive is formatted and contains an operating system. See "Microprocessor" for instructions. Fault Red indicator indicates a problem with the power supply, such as fan failure, voltage level error, or other fault. Check the System Setup configuration settings. weblink
If the problem persists or the computer has integrated graphics, contact Dell. Check the interface cable and power cable connections to the backplane board. If the problem still persists, replace the system board. See "Using the System Setup Program" for instructions.
Use the up- and down-arrow keys to select IDE CD drive from the menu or enter the associated menu option number. Write fault Write fault on selected drive Faulty diskette or hard-disk drive Replace the diskette or hard-disk drive. If the problem persists, replace the system board. 1-2-1 1-2-2 1-2-3 Programmable interval-timer failure DMA initialization failure DMA page register write/read failure Replace the system board. 1-3-1 Main-memory refresh verification failure Make sure you follow each step.
Record the message on a copy of the Diagnostics Checklist, and then follow the instructions in that section for obtaining technical assistance.Alert Log Messages From the Dell OpenManage HIP If the problem persists, replace the DIMMs. See "Getting Help" for instructions on obtaining technical assistance. Alert Uncorrectable Memory Error Has Been Previously Detected In Dimm 2 Remove the diskette and boot with the hard-disk drive or a bootable diskette.
See "Drives." ROM bad checksum = address Expansion card improperly installed or faulty Reinstall the expansion cards. Drive not ready Diskette missing from or improperly inserted in diskette drive Reinsert or replace the diskette. When the DELL logo appears, press
The drive activity light may flash briefly. Dell Support If the problem persists, replace the system board. After you create the floppy disk, exit to DOS. See your Installation and Troubleshooting Guide and the documentation that accompanied the operating system and application program for more information on warning messages.
NOTE: The Service Tag for your computer is located at the top of each test screen. See "Getting Help" for instructions on obtaining technical assistance. Single Bit Memory Error Previously Detected In Dimm 1 Or 2 Determine if a conflict exists by removing a card (not the graphics card) and then restarting the computer. Uncorrectable Memory Error Dell Drive being prepared for removal The three drive status indicators flash sequentially.
Microprocessor not supported by system Install a correct version of the microprocessor in the specified microprocessor connector. http://centralpedia.com/memory-error/uncorrectable-memory-error-dell.html The Windows XP Setup screen appears, and the operating system begins to copy files and install the devices. If you're not already familiar with forums, watch our Welcome Guide to get started. See "System Battery." Invalid CPU speed detected Microprocessor not supported by system Install a correct version of the microprocessor in the specified microprocessor connector. Error Code 2000-0122
Repeat this process for each card. When prompted, type s to select Specify Additional Device. Channel A Not Present, Channel B Not Present Backplane is not in use Continue to boot. http://centralpedia.com/memory-error/uncorrectable-memory-error-previously-detected.html If the problem persists, replace the DIMMs.
Amount of memory has changed Missing or faulty DIMMs Check that DIMMs have not been removed. See "Drives." If the problem persists, replace the system board. Scroll down the list to see if any device has an exclamation point (a yellow circle with a [!]) on the device icon.
To change the restore point, you can either repeat the steps using a different restore point, or you can undo the restoration. If the problem persists, replace the DIMMs. If available, install properly working memory of the same type into your computer. Reseat the memory modules to ensure that your computer is successfully communicating with the memory.
If the system detects a problem with any of the system voltage levels, temperature sensors, fan sensors, hard-disk drive controllers, or PCI expansion cards, this LED blinks amber. Using Microsoft® Windows® XP System Restore The Microsoft® Windows® XP operating system provides System Restore to allow you to return your computer to an earlier operating state (without affecting data files) See "Getting Help" for instructions on obtaining technical assistance. 1-2-2 DMA initialization failure 1-2-3 DMA page register write/read failure 1-3-1 Main-memory refresh verification failure Remove and reseat the DIMMs. this content Enter the date, time, and time zone in the Date and Time Settings window, and click Next.
If the problem still persists, replace the system board. Using Windows XP Device Driver Rollback If a problem occurs on your computer after you install or update a driver, use Windows XP Device Driver Rollback to replace the driver with If the problem persists, replace the memory modules. See "Drives." Replace the diskette-drive interface cable.
Similar Threads - Solved Uncorrectable Memory Solved WHEA_Uncorrectable_Error Windows 10 greenman019, Sep 4, 2016, in forum: Hardware Replies: 6 Views: 163 greenman019 Sep 12, 2016 Requesting Advice on this WHEA_UNCORRECTABLE_ERROR Fine.., Type 1 to start the ResourceCD menu. Unsupported CPU combination. Bad error-correction code(ECC) on disk read Controller has failed Faulty diskette/tape drive subsystem or hard-disk drive subsystem (defective system board) Replace the system board.
agrostis, Mar 1, 2005 #6 Sponsor This thread has been Locked and is not open to further replies. They can assist you with identifying a problem and may provide you with information to help you resolve the problem. See "Drives." Replace the diskette-drive interface cable.