Check for a possible blockage on or inadequate ventilation around the fan. Seek operation failed Faulty diskette or hard-disk drive Replace the diskette or hard-disk drive. See FIGURE 2-1 and FIGURE 2-2. No boot sector on hard-disk drive Enter system setup and ensure that the computer configuration information for the hard drive is correct. http://centralpedia.com/memory-error/uncorrectable-memory-error-previously-detected.html
In the Control Panel window, double-click System. Timer chip counter 2 failed Defective system board Replace the system board. Alert! Windows 2000 Click the Start button, point to Settings, and then click Control Panel. http://capita.wustl.edu/capita/People/agonzalez/vigordoc/2400%20manual/beep.htm
General failure Operating system corrupted or not installed properly Reinstall the operating system. You can customize the tests you want to run. If a faulty system does not emit beep codes or display system error messages to indicate a failure, you should run the appropriate tests in the Dell Diagnostics to help isolate Also, ensure that the processor heat sink is properly installed.
See your Solaris documentation for details. Enter the date, time, and time zone in the Date and Time Settings window, and click Next. Unsupported RAID key detected! Alert Uncorrectable Memory Error Has Been Previously Detected In Dimm 2 Unsupported CPU speed in CMOS Microprocessor not supported by BIOS Upgrade the BIOS.
The Windows XP Setup screen appears, and the operating system begins to copy files and install the devices. Seek error Defective sectors on diskette or hard-disk drive Replace the diskette or hard-disk drive. If the problem persists, replace the DIMMs. Diskette read failure Faulty diskette, faulty or improperly connected diskette/tape drive interface cable, or loose power cable Check that the diskette drive is properly installed on the SCSI backplane board.
Code Cause 1-1-2Microprocessor register failure 1-1-3NVRAM read/write failure 1-1-4ROM BIOS checksum failure 1-2-1Programmable interval timer failure 1-2-2DMA initialization failure 1-2-3DMA page register read/write failure 1-3Video Memory Test failure 1-3-1 through 2-4-4Memory Dell Support For example, before you format a diskette, a message may warn you that you may lose all data on the diskette, as a way to protect against inadvertently erasing or writing Front-Panel Indicators The following indicators are on the system's front panel (see Figure 1, Figure 2 and Table 3): Figure 1. Insert the Operating System CD.
The drive failure indicator blinks on briefly each second. http://en.community.dell.com/support-forums/desktop/f/3514/t/19304616 Press
If the problem persists, replace the DIMMs. have a peek at these guys If the problem still persists, replace the system board. 4-3-3 Defective system board Replace the system board. 4-3-4 Time-of-day clock stopped Replace the battery. When I booted the other day the computer started normally but then a blue screen appeared stating that there was a Hardware Malfunction and the System was Halted. managed replied Oct 30, 2016 at 9:07 PM Loading... Uncorrectable Memory Error Dell
The drive failure indicator blinks briefly each second. Drive ready for insertion or removal All three drive status indicators are off. Previous processor thermal failure The microprocessor exceeded operating temperature during the previous operating session. check over here Temperature sensor detected a failure* A temperature probe on the backplane board, system board, or drive carrier in the specified server has exceeded its temperature failure range.
System halted! If the problem persists, replace the system board. If the problem persists, replace the DIMMs.
If the problem persists, replace the DIMMs. Reinstall the hard-disk drive. Close some programs and try again Close all windows and open the program that you want to use. Type of controller has changed since previous system boot Back up information on the drives before changing the type of controller used with the hard-disk drives.
To see if System Restore is enabled: Click the Start button and click Control Panel. Attachment failed to respond Diskette drive or hard-disk drive controller cannot send data to associated drive Replace the drive's interface cable. See the documentation that came with the software for instructions. this content Each device has its own set of specialized commands that only its driver recognizes.
After the drive is selected for removal, the "drive being prepared for removal" pattern appears, followed by the "drive ready for insertion or removal" pattern. Click Troubleshooting and Maintenance on the Contents tab, click Windows2000 troubleshooters, and then click Hardware. Alert! All calendar dates with available restore points appear in boldface type.
If Device Driver Rollback does not resolve the problem, then use System Restore to return your operating system to the operating state it was in before you installed the new device