Home > Tape Drive > Ultrium Error Codes

Ultrium Error Codes

Contents

The Attention LED is lit but the Cleaning LED is not lit after a cartridge load. When you press Enter, the OCP displays the error message, as shown in Error message in the OCP Error Log (Figure 6). Device error sub-codes Error code Description 81 Drive wake up failed 88 Error accessing slot status 90 Robotic load not reached Cartridge Present sensor 91 No activity after Load command 92 Make sure that the appropriate data cartridge for the model is being used. navigate here

The mini-SAS connector on the tape drive is keyed at location four, which is the standard location for end devices. You might not be able to backup a subset of files or restore a single file. SCSI Host Adapter Installation: Verify that the SCSI host adapter is installed correctly. Use the magazine removal process to release the magazine and remove it from the device. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html

Ibm Tape Drive Error Code 6

To find the performance bottlenecks in your system, check the specifications and performance of the: Average file size File system type Connection from the host server to the disks Operating system When fully used, a 2 GB fibre connection can provide enough bandwidth for an Ultrium 1760 tape drive. This is most likely caused by a dirty drive that cannot read a tape and marks the tape invalid.

  1. If there are no bottlenecks and the Autoloader starts having performance problems: Try a new cartridge.
  2. Use a dedicated disk array or upgrade to RAID 5.
  3. If the failure remains with the same slot, the magazine is probably at fault.
  4. Remove any magazines that contain tapes marked with !.
  5. Your cache administrator is webmaster.
  6. Upgrade to a faster transport medium, such as Ultra 320 SCSI.
  7. top Using HP Library & Tape Tools to diagnose problems With HP Library & Tape Tools installed on the host server, the following tasks can be accomplished: Identify all SCSI devices

The support ticket and report contain the same information. NOTE: Most RAID or array controllers do not provide multiple LUN support. There are three ways to obtain error codes from the device: On the OCP On the RMI On an L&TT support ticket or report Finding error code information on the OCP Tape Drive Determined That A Microcode Error Occurred. Power on device before powering on the host computer.

Make sure that the cartridge is compatible with the drive. Ibm Lto 5 Tape Drive Error Code 6 The process of backing up files goes through many devices, from the files in the file system on the disk, through the backup server, and out to the Autoloader, all managed Please try the request again. click here now If the Media Attention LED is cleared and the drive has been cleaned, and then immediately re-displays each time a particular cartridge is reloaded, that cartridge should be suspected as being

An Ultra 160 connection is barely adequate for an Ultrium 1760 tape drive. Dell Tape Drive Error Codes Errors displayed on the front panel Problem Solution “!” in operator panel inventory display. The device uses two Logical Unit Numbers (LUNs) to control the tape drive (LUN 0) and robotic (LUN 1). The system returned: (22) Invalid argument The remote host or network may be down.

Ibm Lto 5 Tape Drive Error Code 6

Make sure you are using data and cleaning cartridges that are compatible with the drive and model of the device (see the Tape cartridges section in Tape Cartridges and Magazines ). Native backup applications based on tar, cpio, NT Backup, etc. Ibm Tape Drive Error Code 6 Some backup software packages require an additional module to communicate with the robotics. Dell Lto 5 Tape Drive Error Code 6 Since Novell volumes may be compressed, hardware compression may lower the performance and capacity.

If the mini-SAS connectors that connect to the tape drive and some HBAs will not plug in, check the key. check over here LTO-3: MARGINAL. Unless otherwise listed in Operation problems , try to resolve the error by cycling power to the device and retrying the operation. Run advanced diagnostic tests, including connectivity, read/write, media validation, and testing the functionality of the device. Ibm Tape Library Error Codes

Third, have you tried a firmware update?   Thanks, James Braunstein I.T Administrator 0 Jalapeno OP Teplcon Oct 12, 2011 at 12:01 UTC Cyscore, Thanks for the input! Also, make sure that the server or workstation is used as little as possible during the backup, and close down programs such as virus scanners, which check each file that is Elevator: The part of the robotics assembly that moves in the vertical direction. his comment is here Ensure that the device is either mounted in a rack with its rack kit or in a tabletop conversion cover.

Creating your account only takes a few minutes. Tape Drive Or Rs-422 Error If you are doing an operation that automatically returns a tape cartridge to a certain slot, make sure another tape is not loaded in that slot. A cleaning cartridge is good for 50 cleans.

Make sure the power cord is connected.

NOTE: Processor speed numbers as based on Intel x86 type processors. The READY light flashes while the tape rewinds. LTO-3, LTO-4: POOR. Dell Tape Drive Error Code 7 Main error codes Error code Description Details and solution 80 Cannot initialize bar code reader Power-cycle the unit and retry the operation 81 No response from bar code reader 82 No

Internal disks on backup server POOR. Replace the magazines. NOTE: The tape drive must rewind the tape before ejecting it. http://centralpedia.com/tape-drive/ultrium-lto-3-error-codes.html Some backup software packages require an additional module to communicate with the robotics.

This length must be included in any calculations of cable length. Make sure that the host adapter is properly seated in the motherboard slot and the operating system correctly detects the host adapter. It can be downloaded free of charge from http://www.hp.com/support/TapeTools .