Home > Tape Drive > Ultrium Lto 2 Error Codes

Ultrium Lto 2 Error Codes

Contents

The error sub-codes are described in Error sub-code descriptions . Easily update device and drive firmware. Parallel SCSI: Ultra Wide, Fast Wide POOR. Parallel SCSI: Ultra 160 LTO-2: GOOD. navigate here

In the backup software, verify that hardware data compression is turned on and software data compression is turned off. Check the cartridge for damage. The disadvantage is that backup and restore operations work on an entire disk, partition, or LUN. Try the following steps, in this order, to remove the stuck tape. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html

Ibm Tape Drive Error Codes

Replace the magazines. Change the Startup type to Disabled and click OK. Make sure that the cartridge is compatible with the drive. Complete the cleaning process and retry the operation. 61 Cleaning failure.

  • Do not degauss Ultrium cartridges!
  • If the mini-SAS connectors that connect to the tape drive and some HBAs will not plug in, check the key.
  • No change is necessary but using a sequential backup method, such as an image backup, could offer some performance gains.

None. The system returned: (22) Invalid argument The remote host or network may be down. Ultrium 1760: MARGINAL. Tape Drive Determined That A Microcode Error Occurred. Avere Caching Servers Implement an Avere Systems FXT-3200 cluster to improve storage array I/O performance.

Check the length and integrity of your SAS cabling. Some backup software packages require an additional module to communicate with the robotics. Or click the Support button on the main toolbar to display the Support screen for additional report or support ticket options. https://community.spiceworks.com/topic/158752-ultrium-lto-2-error-codes When fully used, a 2 GB fibre connection can provide enough bandwidth for 4 LTO-2 tape drives.

If the problem continues, contact HP customer support. Ibm Tape Drive Diagnostics Full-featured backup applications also offer the best speeds for single file restores and allows for backing up only specific data. Errors displayed on the front panel Problem Solution “!” in operator panel inventory display. Image or sequential backup None.

Ibm Lto 5 Tape Drive Error Code 6

Check that the device is fully powered up and is not in an error state. If the error persists, contact support personnel. Ibm Tape Drive Error Codes Insert a USB flash drive into the USB port on the rear panel and then from the OCP, select Download support ticket to USB. Ibm Tape Library Error Codes Add-in RAID controllers, RAID on a chip (ROC), RAID on the mother board (ROMB), internal parallel SCSI, and internal IDE (non-RAID) are inadequate transport mechanisms for tape drives.

I was hoping that since this came "refurbished" from Ebay that may have been taken care of, but I'll look into it. http://centralpedia.com/tape-drive/ultrium-error-codes.html Upgrade to Gigabit Ethernet or Fibre Channel. top top Error sub-code descriptions Robotic error sub-codes The following table lists the robotic error sub-codes. Make sure that you understand any data protection or overwrite protection schemes that the backup application may be using, which could prevent you from writing to a given cartridge. Ibm Ultrium-hh3 Status Lights

Discard any tape cartridge found to have issues. The bus would be saturated with 2:1 compressible data. SCSI bus not properly terminated (see SCSI Installation problems ). his comment is here A cartridge recently imported from a different environment is causing issues.

Initiate the firmware upgrade process before loading a firmware upgrade tape into the drive. 65 Invalid upgrade cartridge. Tape Drive Or Rs-422 Error Make sure the backup server has enough memory to handle the bandwidth of the backup or restore. From the OCP, attempt to unload or move the tape to a slot.

Anyone clue me in on the error codes, or know where I can get a hold of a manual?

The entire disk contents is backed up contiguously, without the disk seeking, which prevents performance degradation caused by small or fragmented files. Reboot the host server. It uniquely maps to an error code. Lto Tape Drive Error 6 Power cycle the unit.

Please try the request again. Verify that the cartridge is a firmware upgrade cartridge, not a data or cleaning cartridge. top top Connection from the host server to the Autoloader For the best performance, the connection from the host server to the Autoloader must have enough bandwidth to provide enough data http://centralpedia.com/tape-drive/ultrium-lto-3-error-codes.html Reload the magazines with tapes that have passed inspection and new tapes to replace cartridges that did not pass inspection.

LTO-3, LTO-4: POOR. If the problem continues, contact HP customer support. top Operating system configuration The operating system configuration and other programs running on the host computer can impact the ability of the host computer to transfer files from the disks to An Ultra 2(80) connection is inadequate for an LTO-3 or LTO-4 tape drive.

top SCSI installation problems Problems encountered during installation are usually caused by improper SCSI bus configuration, application software configuration errors, or an incorrectly configured operating system. Join the community Back I agree Powerful tools you need, all for free. The inventory process takes a long time Apply high-quality HP labels to all tape cartridges. View detailed configuration, identification, inventory, and drive information for the device.

This is most likely caused by a dirty drive that cannot read a tape and marks the tape invalid. The LCD displays an error code. top top Service and repair Removing stuck tapes from slots NOTE: Contact an HP support representative if a cartridge is stuck in the drive. Check the SCSI connector for bent pins.