Home > Tape Drive > Ultrium Tape Error 8

Ultrium Tape Error 8

Contents

To generate and view a report or support ticket from L&TT: In the L&TT By Product or By Connection tab, select the device from the device list. Make sure that the cartridge has not been exposed to harsh environmental or electrical conditions and is not physically damaged in any way. To use the operator control panel. The bus would be saturated when providing 2:1 compressible data to an LTO-3 tape drive. navigate here

Make sure that the cartridge has not been exposed to harsh environmental or electrical conditions, and is not physically damaged in any way. The STOP sign icon and the word Crit before the event ID also indicate a hard error. SCSI bus not properly terminated (see SCSI Installation problems ). If the parallel SCSI cables are not designed for Ultra 320 speeds or more than a couple devices are on the parallel SCSI bus, the bus may slow down to Ultra http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html

Ultrium Tape Drive Error Codes

top Backup type Each type of backup has its own impact on performance, depending on how well it can keep data streaming to the tape drive. LTO-3, LTO-4: POOR. If other tapes are still in the device, or if it is unable to manually remove the magazines and drive, contact HP service for further instructions. The top of the support ticket contains basic configuration information about the device, as shown in Support ticket in viewer (Figure 10).

Check the SCSI connector for bent pins. An Ultra 2(80) connection is inadequate for an LTO-3 or LTO-4 tape drive. Slider: The part of the robotics assembly that plunges in and out for get and put operations. Tape Drive Or Rs-422 Error See below for steps to manually release the magazines if magazines cannot be removed via OCP or RMI. 2.

Some backup software packages require an additional module to communicate with the robotics. During the inventory process, the bar code reader attempts to read the bar code on the cartridge or the bar code on the back of the storage slot until it identifies If the autoloader is not mounted in a rack or in the tabletop conversion cover, ensure that the six support feet are installed and that all of them are standing on here To find the performance bottlenecks in your system, check the specifications and performance of the: Average file size File system type Connection from the host server to the disks Operating system

The reader can usually identify a properly-labeled cartridge the first time, while determining that an unlabeled cartridge is in a storage slot can take four times as long. Ibm Ultrium-hh3 Status Lights See below for steps to execute the test. If the RMI web page does not display, ping the device’s IP address. NOTE: The support ticket downloaded from the RMI will only contain information about the Autoloader.

  1. Ultra 160 is a good transport medium, but does not have enough bandwidth for LTO-3 or LTO-4 tape drives.
  2. DLT VS80, Ultrium 232, Ultrium 448 and Ultrium 960 models: check that the HBA supports LUN scanning, and this feature is enabled.
  3. Before installing a driver, make sure it is not in conflict with the application software.
  4. This can take as long as five minutes, depending on how much tape must be rewound.
  5. Export the media to clear the state.

Ibm Tape Library Error Codes

Media Cleaning or data cartridge incompatible with drive Make sure users are using data and cleaning cartridges that are compatible with the drive and model of the autoloader (see Cartridge type Make sure there is power to the outlet. Ultrium Tape Drive Error Codes Inspect each removed tape for damage, check that the tape is compatible with the drive, and ensure that it is not past its usage life. Tape Drive Determined That A Microcode Error Occurred. For good performance, use a faster connection with LTO-3 and LTO-4 tape drives.

If there is a combination of LVD and SE devices on the bus, the maximum cable length reverts to the SE specification, which for Ultra devices is 10 feet (3 meters) http://centralpedia.com/tape-drive/ultrium-4-tape-drive-error-code-6.html In the Administrative Tools, select Services. Make sure the autoloader and tape drive are on their own SCSI bus and not daisy-chained to another tape drive or to the hard drive being backed up. If you are backing up data over a network, consider comparing the performance to a local-only backup. Dell Lto 5 Tape Drive Error Code 6

Use the latest versions of the databases. Make sure you are using an Ultrium universal cleaning cartridge (see the Tape cartridges section in Tape Cartridges and Magazines ). Retry the operation with a different, known good tape. his comment is here Tape stuck in storage slot.

An Ultra 2 (80) connection is inadequate for an LTO-3 or LTO-4 tape drive. Dell Tape Drive Error Codes Refer to the manuals supplied with the other devices on the SCSI bus for information on enabling or disabling termination on those devices. Figure 6: Error message in the OCP Error Log If you press Next, the OCP will display additional information, if available, as shown in No additional information in the OCP error

Parallel SCSI: Ultra 2 (80) LTO-2: MARGINAL.

It could be a defective cartridge. The error sub-code (0x02) is displayed in parenthesis as the Module error code. Cleaning problems Problem Solution Cannot load the cleaning cartridge. Ibm Tape Drive Diagnostics Export the data cartridge.

Ultra Wide and Fast Wide are inadequate transport mechanism for Ultrium tape drives. Drive error codes Error code Description 01 Drive broken 02 Temperature exceeds limit 03 Tape error 04 Cleaning cartridge is expired 05 Drive needs cleaning 06 Autoloader lost communication with the There are three ways to obtain error codes from the device: On the OCP On the RMI On an L&TT support ticket or report Finding error code information on the OCP weblink If you are more concerned about backup performance than single-file restore, disk image or sequential backups can offer a real performance benefit.

Make sure that the proper device driver is installed for the SCSI host adapter. The bus would be saturated when providing 2:1 compressible data to an Ultrium 1760 tape drive. Retry the operation with a different, known good tape. Figure 5: Error code in the OCP Error Log The code 9B is the main error code, 37 is the error sub-code, and 31 is sub-code specific information for factory use

If the problem continues, contact HP customer support. NOTE: Many backup applications use their own drivers. Make sure the autoloader is connected to a LVDS SCSI bus, and there are no SE devices on the same bus, because this will cause the entire bus to negotiate down Provide feedback Please rate the information on this page to help us improve our content.

Fibre: 2 GB GOOD. Initiate the firmware upgrade process before loading a firmware upgrade tape into the drive. 64 Invalid cleaning cartridge. Power the autoloader OFF and back ON. 5. Initiate the firmware upgrade process before loading a firmware upgrade tape into the drive. 65 Invalid upgrade cartridge.

An Ultra 160 connection is barely adequate for an LTO-3 tape drive. Manually remove the cartridge from the magazine by inserting a finger in the hole at the back of the magazine. None. The mini-SAS connector on the tape drive is keyed at location four, which is the standard location for end devices.

The drawback of using concurrency is that restore operations take longer. If cables not designed for Ultra 320 speeds are used or there are more than a couple devices on the bus, the bus may slow down to Ultra 160 speeds.