Home > Ultra 3000 > Ultra 3000 Servo Error 11

Ultra 3000 Servo Error 11

Contents

gmfergNovember 28th, 2009, 01:16 PMFrom the Ultra 3000 Manual: 12165 12166 Check the encoder wiring again and make sure shield connection is made per installation manual. When the feed rolls accelerate from a standstill to the programmed feed velocity, energy is transferred to the material by the gripping and rotating force of the rollers. Stock Straighteners How far should the Straightener be from the Feeder? May also be caused by defective encoder cable, or bad connections to encoder. navigate here

Please try the request again. But as a general rule, the harder and/or thinner the material, the more straightening rolls are needed. Generated Mon, 31 Oct 2016 00:23:16 GMT by s_wx1194 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection Replace if damaged.-Motor's Hall effect encoder damaged. see here

Allen Bradley Ultra 3000 Error Codes

fordNovember 28th, 2009, 10:35 PMyes thanks gmferg the phase from the motor is correct according to the manual,also the encoder feed back from the motor goes into a break out box WD-40’s chemistry contains materials that are extremely harmful to Buna-N O-Rings. An example would be: Feed Cam close at 270 degrees, Feed Cam open at 90 degrees.

  • How do I make the Reel turn faster?
  • This is repeated until the problem is cleared.
  • How do I know the maximum coil weight I can expect my Stock Reel to support?
  • The two cams are never on at the same time.
  • The system returned: (22) Invalid argument The remote host or network may be down.
  • top Why is the Feeder inaccurate?

This trapped air is throttled through the Speed Adjustment Screw to allow control of the feed head feeding speed.If air is leaking at any other time, it indicates a failed o-ring What is a SYNC-FAULT? The person who wired it did not know that the motor shield should of been grounded on the drive casing it was removed at the electrical pannel entrance as well as Ultra 3000 Intex Type controls, D.C.

Register a new account Sign in Already have an account? Ultra 3000 Software Generated Mon, 31 Oct 2016 00:23:16 GMT by s_wx1194 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection Sign In Now Sign in to follow this Followers 0 Go To Topic Listing Allen Bradley All Activity Home PLCs and Supporting Devices Allen Bradley Problem with Ultra 3000 and MPL https://www.scribd.com/doc/55086623/Ultra-3000-Drive-2098-in003-en-p Incorrect motor chosen.

The P/A Air Feeds are not able to reverse the feed direction. Allen Bradley Ultra 3000 Error Code E24 This amount can vary slightly depending on the size of the feeder, the stroke length, and cycles per minute.Remember, this is an AIR Feed, not a HYDRAULIC feed. Your cache administrator is webmaster. If the press stops in a location where both cams are closed, the Feeder (if in Auto mode) will continually feed material without regard to crank rotation.The Feed Cam should close

Ultra 3000 Software

top How many cycles/strokes can I expect from my Air Feed before I will need to install a repair kit? http://forums.mrplc.com/index.php?/topic/25717-problem-with-ultra-3000-and-mpl-motor/ A completed circuit of this voltage indicates to the Servo Drive, that the motor is within operating temperature. Allen Bradley Ultra 3000 Error Codes top O.K., so how do I fix roll slippage? Allen Bradley Ultra 3000 Error Code E19 Replace if damaged.-Motor's encoder damaged.

I was concerned for noise, however I do not think this is the problem. check over here Basically, anything that can cause the motor to lock-up, or be difficult to turn.-Incorrect Motor Phasing. How far should the Straightener be from the Feeder? The fault cannot be cleared online. Allen Bradley Servo Drive Fault Codes

It is NOT a servo drive error.-Check feed to press timing to assure feed length can be completed within the given feed cam window. Sign In Sign Up Browse Back Browse Forums Downloads Calendar Staff Online Users Activity Back Activity All Activity Search © MrPLC.com  |  Terms of Use    Privacy Policy Contact Us Links Articles Downloads Forums Home The accuracy of this number is based on the roll’s diameter, the motor’s encoder resolution and gearing, scale parameter, etc. http://centralpedia.com/ultra-3000/ultra-3000-error.html O.K., so how do I prove my inaccuracy is not a Feeder control problem?

top What is a SYNC-FAULT? Allen Bradley Ultra 3000 Error Code E30 Determine Ultra3000 Drive Status Error Codes The following list of problematic symptoms (no error code shown) and problems with assigned error codes is designed to help you resolve anomalies. Please try the request again.

If at any point in the revolution of the Crankshaft the two signals overlap, or are both closed, the Feeder will do multiple indexes.

top What type, and how much oil should I put into my Air Feed? All Ultra3000 drives Flashing E followed by two numbers Your Ultra3000 drive has an error. It has been my experience with these drives (actually their predecessors) that the behavior you describe is always caused by a motor feedback or cable problem. Allen Bradley Ultra 3000 Error Code E09 Error Code Problem or Symptom Possible Cause Action/Solution Power (PWR) indicator not ON No ac power or auxiliary logic power.

P/A recommends a light (30-32 weight), hydraulic oil such as Shell Tellus Plus 32 or equivalent. from the Feeder. Can I use WD-40 to clean the Air Feed? weblink Each roll following the first applies slightly less bending moment until the material exits.

Gravity pulls the loop downward causing pull on the feeder’s clamps opposite to the feed direction. At the Motor's designed high temperature limit of 140 degrees Celsius (284 degrees Fahrenheit), the Thermistor’s decreased resistance triggers a fault circuit. The heavier gauge wire springs are placed under the Stock Clamp on the feed body. Ultra Edge and Advantages have a roll circumference of 11.142 inches or 283 mm.

For instance, P/A Model: SRA-2624-D = translates to: Stock Reel Adjustable- “2600” Pound capacity with a maximum “24” inch material width (2624), - Dancer Arm speed/loop control. Lower the deceleration parameter.-Line voltage spikes can send the Bus Voltage over it's maximum threshold. top The Air Feed’s clamps have different coil springs; one set is lighter gauge wire than the other set. Manuals Directory ManualsDir.com - online owner manuals library Search Directory Brands Rockwell Automation manuals Equipment 2090 Ultra3000 Servo Drives Integration Manual Manual General troubleshooting, Error codes, Error codes on – Rockwell